"Parallel world map" illuminated RGBW picture 230V 125x73cm

Code: 4709/BUK 4709/BIL 4709/DUB 4709/DUB2 4709/CER 4709/JED 4709/ORE 4709/OLI Choose variant
Brand: Li-Go
€363 / pcs €378 / pcs €363 / pcs €373 / pcs €363 / pcs €363 / pcs €363 / pcs €363 / pcs from €363 / pcs
in stock in stock in stock.. in stock... in stock in stock in stock in stock Choose variant
decor - surface
Chosen variant is not available. Reset selected parameters.

The lamp can be connected:

  • Directly into a 230V socket
  • Connection to the prepared 230V wall outlet (the supply cable is shortened and connected to the 230V wall outlet) It is advisable to have the wall outlet anywhere in the lower part of the lamp, no more than 5 cm from the bottom edge.
  • In our offer, you can find a variant of a battery-powered lamp, more in the category " Light paintings with batteries "

NOTE: The lamp is open at the back (it does not have a back plate) and therefore the light also radiates to the sides. However, it is necessary to keep in mind that some defects on the wall may be visible through the cut parts. Therefore, we recommend having a clean and straight wall for hanging.

Included in the fixture:

  • Power cable white 3m
  • There is a button on the bottom of the lamp that can be dimmed and turned off
  • Receiver for remote control (you only need to purchase the controller model as needed for the lamp)
  • Two staples with a dowel, diameter 5 mm, are included for fixing to the wall

Remote control. It is possible to purchase a remote control for the lamp, which we offer in several versions. You can order in the " Accessories " section

Control using a so-called smart home or connection with the ZIGBEE, Philips HUE or IKEA TRADFRI systems is possible, but this modification must be ordered.

Additional light: You can purchase a powerful additional LED for the lamp light that makes it possible to read, for example. The additional light includes a touch control. The control of the additional light is independent of the LED image and is dimmable separately.

2222

ENGRAVING: You can have a text (e.g. wish or motto) engraved on the lamp. When ordering, just write the desired text in the order notes and we will engrave it for you.

The item " Engraving " must be added to the cart.

engraving 2

SURFACE DESIGN:

  • Birch is velvet matte, has a smooth surface with a very fine grain of wood and almost no knots. Thanks to its very bright design, it creates a strong contrast with the cut black edge
  • Oak A has a surface with a fine wood structure (relief), semi-matte. We classify the shade as lighter. The knots are dark, expressive and stand out from the fine grain of the wood.
  • Oak B has a surface with a fine wood structure (relief), semi-matte. The shade is honey, if it gets direct sunlight it is more yellow. Fine black lines run through the grain of the wood, this is the most popular shade. We recommend it if you are buying the product as a gift (surprise).
  • Walnut has a surface with a fine structure (relief) of wood, semi-matte. Dark shade, the grain of the wood does not stand out much, the shade is brown including the knots. The cut (black) edge does not stand out too much on the nut.
  • Black with patina , the surface is smooth and matte, reminiscent of an annealed metal sheet, the gray surface is also similar to anthracite, it goes well with black shades (e.g. furniture).

 

 Material/Backing plate:

  • Traditional pressed MDF board 8mm. It is produced by the dry method, by chopping the remains of hard and soft wood into wood fibers, which, thanks to the content of lignin *, are suitably combined with wax and a resin binder. They are then formed into plates under high pressure and temperature. The advantage is good strength and excellent machinability. A decor is pressed on the board - a surface that is made of different woods, textures or pure white. The surface is easy to care for, resistant to moisture or direct sunlight (UV radiation).
  • Our MDF boards are manufactured in accordance with the European standard EN622, and are supplied only from European suppliers with FSC certification.
  • MDF - unlike veneered or plywood boards, the material is defect-free, does not warp, crack, fade or darken.

Ecology:

  • Thanks to its long service life (tens of years), it is a very ecological product, moreover, all electrical components can be easily replaced. We believe that our images will still shine on our children.
  • The wood from which the boards are made is the most sustainable building material - a renewable resource that stores a huge amount of carbon. No trees are needlessly cut down, the boards contain up to 65% residues from sawmill production and 87% are materials from renewable sources.

 

LED lighting

The LED strips are equipped with high-quality San'an SQ (super quality) LED chips with a lifespan of 50,000 hours at full brightness. At the same time, light images are ideally backlit at 80% brightness, which significantly extends the life of the light source (LED strip). You can find detailed information about the light source in the ENERGY LABEL/PRODUCT INFORMATION SHEET tab.

Detailed information

Product detailed description

The lamp can be connected:

  • Directly into a 230V socket
  • Connection to the prepared 230V wall outlet (the supply cable is shortened and connected to the 230V wall outlet) It is advisable to have the outlet from the wall anywhere in the lower part of the lamp, we recommend within 5 cm from the bottom edge, or you need to think about the connection not being visible through a cut motif.

Included in the fixture:

  • Power cable white 3m
  • RGB remote control
  • Receiver for remote control
  • Two staples with a dowel, diameter 5 mm, are included for fixing to the wall

Additional light: You can purchase a powerful additional LED for the lamp light that makes it possible to read, for example. The additional light includes a touch controller, which is located on the side of the lamp. The control of the additional light is independent of the image backlight and is dimmable separately.

Lamp size: You can order a picture lamp  also in a different size, or modify the carved motif or the colors of the backlight.

Motion sensor: We will install a motion sensor in the light you purchased from us. This only lights up the picture in your presence, thus saving energy. The modification can be ordered " here "

NOTE: The lamp is open at the back (it does not have a back plate), thanks to which the light also radiates to the sides. It should be kept in mind that some imperfections on the wall may be visible through the cut sections. The wall does not have to be white, and there is no problem if it is uniformly porous (e.g. some rough stucco).

ENGRAVING: You can have a text (e.g. wish or motto) engraved on the lamp. When ordering, just write the desired text in the order notes and we will engrave it for you.

The item " Engraving " must be added to the cart.

engraving 2

SURFACE DESIGN:

  • Birch is velvet matte, has a smooth surface with a very fine grain of wood and almost no knots. Thanks to its very bright design, it creates a strong contrast with the cut black edge
  • Oak A has a surface with a fine wood structure (relief), semi-matte. We classify the shade as lighter. The knots are dark, expressive and stand out from the fine grain of the wood.
  • Oak B has a surface with a fine wood structure (relief), semi-matte. The shade is honey, if it gets direct sunlight it is more yellow. Fine black lines run through the grain of the wood, this is the most popular shade. We recommend it if you are buying the product as a gift (surprise).
  • Olive is velvety matte, has a smooth surface, light to medium dark shade. It has a distinctive wood grain and is completely knot-free. The shades are very warm, ocher to orange .
  • Fir has a surface with a fine structure (relief) of wood, semi-matte. It is a medium-dark shade, it has a distinct wood pattern, as well as knots. It has a rustic feel.
  • Walnut has a surface with a fine structure (relief) of wood, semi-matte. Dark shade, the grain of the wood does not stand out much, the shade is brown including the knots. The cut (black) edge does not stand out too much on the nut.
  • Black with patina , the surface is smooth and matte, reminiscent of an annealed metal sheet, the gray surface is also similar to anthracite, it goes well with black shades (e.g. furniture).
  • The white is in a matte finish .

Individual decors are photographed in neutral light and together, so you can objectively assess their shade. More info " here " .

Material/Backing plate:

Fibreboard 8mm. A medium-hard wood fiber board on which a wooden or other decor is pressed. The surface is easy to care for, resistant to moisture or direct sunlight. More information about our current offer: " Decors - surface treatment " .  The selected motif is carved into the plate, the plate is reinforced around the perimeter with a frame that is glued to the back of the lamp. 

ENERGY EFFICIENCY: Our lamps are very economical and have a minimal carbon footprint from the electrical energy consumed. We measured the real consumption on a wattmeter. When the lights are on for 8 hours a day (with the maximum light on), the monthly cost of electricity is CZK 2.50 (calculated from the maximum capped price of electricity in 2023).

LED lighting/light source replacement:

The LED strips are equipped with high-quality San'an SQ (super quality) LED chips with a lifespan of 50,000 hours at full brightness. At the same time, light images are ideally backlit at 80% brightness, which significantly extends the life of the light source (LED strip). You can find detailed information about the light source in the ENERGY LABEL/PRODUCT INFORMATION SHEET tab. If your LED strip does get damaged, for example during handling or you decide on a different shade of light, we will gladly replace the LED strip for you or you can replace it yourself. Contact us for more information.

Additional parameters

Category: Light pictures 230V
Weight: 12
Decor: according to variant selection
Material: fiberboard
Location: on the wall
Resource performance: 15W - 24W
Protection class (IP): IP20 - not waterproof
Dimmer controller: remote control with memory of the last setting
Dimensions (w x h x d): 125x73x4cm
Electrical protection: class II
The color of the decorative light: RGBW
Replaceable light source: Yes
Output voltage/current of the source: 12V DC/1.5A-2A
Input voltage of the lamp/source: 100-240V AC
Lifetime of the LED light source: 50,000 hours at full intensity
Possibility to connect a remote control: any number of controllers can be paired
Input/current for decorative light: 1m LED strip 4.8W/0.4A
Energy class of the LED light source: F